Wenn Du auf Nummer Sicher gehen möchtest, lade Dir nochmal das offizielle LibreELEC in der aktuellsten Version herunter und spiele es auf Deine SD Karte. bestellt meinst Du einen Raspberry Pi Modell B+, oder? Das macht es auch fast unmöglich, Fehler genau zu lokalisieren. LibreELEC.īei solchen Builds/Paketen weiß man nie genau, was alles installiert wurde bzw. Wir unterstützen hier keine sogenannten "Builds" oder sonstige "Sondereditionen" von Kodi bzw. Ich wäre euch für Info's/Lösungsvorschläge sehr dankbar, denn auch bei Ubuntu bin ich immer noch frischer Neuling, beim Pi erst Recht. Den kann ich natürlich bei Bedarf gerne hier 'reinkopieren. Ich habe einen Dump des log-Files in meiner Zwischenablage. Könnte mir jemand helfen und mir sagen, was ich hier falsch mache? Lange Rede kurzer Sinn: Auch mit dieser Installation ist mir nicht möglich, Addons zu installieren. Allerdings zeigt mir der Pi stets nur 0% Datenverbrauch dieser Partition an. 13,5GB mit ext4 formatiert und nutzbar sind. Nachdem ich das System mit Hilfe einiger "unprofessioneller Hilfestellungen" aus dem Netz komplett verrammelt hatte, habe ich mir LibreElec 8.0 als Image für eine 16GB-SD-Karte heruntergeladen und die Karte damit betankt. Stets wurde beim Versuch Addons zu installieren die Fehlermeldung "Installation fehlgeschlagen" ausgespuckt. Allerdings konnte ich nur das Wetter-Addon installieren, danach war Schluss. Die Einrichtung/Einbindung in mein Heimnetzwer (Fritz!Box, Ubuntu 12.04 und Zugriff via SSH) lief problemlos. eine 16GB-SD-Karte mit instaliertem Image für LibreElec 7.0.9(?).ĭie Erstinbetriebnahme lief klaglos. And if you’re still watching the log file on the “master” you see the magic start to happen.Seit zwei Wochen bin ich stolzer Besitzer eines Raspi.We called our devices TOP and BOTTOM and gave them ID’s of 1 and 2.So to join our HA master on eth3 all we needed to do was:.To enable Cluster mode, please specify these parameters: To enable HA mode, please specify these parameters: To enable Zeroconf mode, please specify these parameters: To disable Zeroconf/HA/Cluster mode, please use: The key command here to setup HA is sethacfg.You should then end up logged in at the # prompt.Then just enter the New password you’d like to use. For the current password you can put anything, we left it blank. You’ll be asked to change the password.If you haven’t got a fresh box then use the LCD panel to reset it to Factory Defaults. Do not put the USB stick into it, we don’t want any config at all. Power up the “slave” whilst it’s completely factory fresh.Now for the bit Sophos struggled to tell us. If you view the log eventually you’ll see entries appear about waiting for the interface to come up. We then set the Configuration method to Manual and set the NIC to eth3 (which is supposed to be the default HA NIC), set the Device Name, Set as Node ID 1 and put in an encryption key.Go to “Management”, “High Availability” and set the Operation mode to “Hot Standby (active-passive)”.Upload your working license file – this is probably the first thing you’ll see when you get to the Web GUI.Plug the USB stick into the “master” and power it on.Take the backup file from the old UTM525’s and place in the root folder of a Fat32 USB stick.It was a far simpler solution to just go to the “slave” console CLI and enable HA with no other messing about halfway setting up the UTM. I tried asking the Sophos engineer how to configure HA by CLI and the response was to setup the “slave” following the basic setup, giving it an IP address and then going to the “slave” Web GUI to turn on HA – what a waste of breath. Then power on the factory default “slave” and presto HA deals with sync’ing the configs. Previously the installation process was power on the “master” enable HA in the web GUI and set it to automatic on eth3. Sophos/Astaro no longer seem to configure the base images to automatically enable HA. So the slave wasn’t connecting at all.Īfter a long, frustrating and totally fruitless call to Sophos support – never have I felt so let down by Sophos, we discovered the problem. We’d see the “master” that we were configuring dropping log entries that it was waiting for the interface to come up. We had one box up and running very quickly, but getting HA activated seemed not to connect as expected. The one thing we didn’t expect was problem getting the two UTM430’s to configure themselves using High Availability (HA). On the one hand it gave us plenty of time to plan for the eventualities like Martians and be confident that the configuration restore testing worked whilst testing. We encountered a few problems with licensing when we looked at moving from the UTM525’s to UTM430’s so we had to delay the project until yesterday.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |